FIVER POWER BRAKE PARTS | Chongqing, China · since 2005

Design, manufacture and distribution of
auto power brake parts
and electric parts

Index: Power brake booster Brake caliper Master cylinder

Brake Wear Is Becoming a Regulated Emission: What Euro 7 Changes for Discs, Pads and Calipers

Euro 7 introduces brake particle limits: how the PM10 values, UN GTR 24 testing and the 2026-2035 timetable change discs, pads, calipers and aftermarket parts.

Brake dust used to be merely aesthetic: it darkened wheels, washed off at the car wash, and had no regulatory consequence. That changed with Regulation (EU) 2024/1257, the Euro 7 package, which for the first time sets legal limits on the particles a vehicle's brakes may emit. The first limit is for PM10 mass, applying to new vehicle types from 29 November 2026 and all new M1 and N1 vehicles from 29 November 2027, and demonstrated on a brake dynamometer under UN Global Technical Regulation No. 24. It is the first time a regulator has written a number against the friction pair.

The number is per vehicle and per kilometre, not per part. It is met by a vehicle type tested with the manufacturer's friction pair, while the part that generates the particles is a wear item replaced several times over a vehicle's life. The regulation is therefore not a product certificate for a pad or a disc, but a signal about which friction pairs, disc surfaces and caliper behaviours will be specified.

Beyond the tailpipe: why brake wear particles matter

The regulation defines particulate matter as material emitted from the tailpipe or the brakes and collected on a filter, PM10 as particles below 10 micrometres, and brake particle emissions as particles from the brake system. That puts brake dust in the same legal category as exhaust soot.

The scientific case predates the law. Grigoratos and Martini (2014) reported that exhaust and non-exhaust traffic sources are estimated to contribute almost equally to traffic-related PM10, and that in urban environments brake wear can contribute up to 55% by mass of total non-exhaust traffic-related PM10 and up to 21% of total traffic-related PM10. They concluded that as exhaust control becomes stricter, non-exhaust sources, and therefore brake wear, will grow in relative importance. The regulation's own impact assessment goes further, expecting that by 2050 non-exhaust emissions will constitute up to 90% of all particles emitted by road transport.

Health is why the numbers matter. Christou and colleagues (2025) reviewed studies on the impact of brake and tyre particles on human, mammalian, aquatic and terrestrial cells and organisms. The direction is clear even where findings differ: brake and tyre emissions are becoming the major transport-related contributor of particulate matter pollution in cities. Brake particles are not one substance. Gong et al. (2026), testing on a UN GTR-24-compliant platform, found particles from non-asbestos organic (NAO) and low-metallic (LM) pads dominated by iron oxides, with adsorbed water and organic compounds also detected.

What Euro 7 actually requires

Table 4 of Annex I sets the first-stage limits: milligrams of PM10 per kilometre, by powertrain technology, for M1 and N1 vehicles excluding N1 Class III, applying until 31 December 2029.

Powertrain technologyPM10 limit, M1 and N1PM10 limit, N1 Class III
PEV (battery-electric)3 mg/km5 mg/km
OVC-HEV, NOVC-HEV, FCV/FCHV, ICEV7 mg/km11 mg/km

Every powertrain other than battery-electric shares the 7 mg/km limit; only PEV gets the stricter 3 mg/km value. N1 Class III, the heavier light commercial class, is treated separately, at 5 mg/km for PEV and 11 mg/km for the rest.

The testing basis is explicit. Annex III Table 4 requires testing according to UN Global Technical Regulation No. 24 on brake emissions, and Table 11 identifies the brake system emissions test in the WLTP brake cycle as required for type-approval and conformity of production, though not for in-service conformity. Under Article 21 all of this applies from 29 November 2026 for new types of M1 and N1 vehicles and for components, systems and separate technical units intended for them, and from 29 November 2027 for all new vehicles and components.

The first stage is not the end. Tables 5 to 8 of Annex I hold second-stage limits from 1 January 2030, to be set by delegated acts after a Commission review of brake particle measuring methods and the state of the art, due by 31 December 2027. Those tables add a brake particle number (PN) row alongside PM10 mass, and the 2035 table already points to 3 mg/km for M1 and N1 vehicles across all powertrain technologies. The direction is a mass limit now, a number limit next, and convergence on today's strictest value later.

How the limit is measured, and why that shapes the parts

A PM10 limit in milligrams per kilometre sounds like a fixed material property. It is not. Mathissen and colleagues (2018) built a real-world braking cycle from the WLTP reference database, using in-use driving data from five world regions and 740,000 km, because earlier studies used incomparable braking conditions. Testing the cycle on a dynamometer and at vehicle level, they reported that below a disc temperature of 160 degrees Celsius particle number emission is at background and that it sharply increases above that.

Hesse et al. (2021) tested grey cast iron, tungsten carbide-coated and carbon ceramic discs on an inertia dynamometer over a WLTP-derived cycle. They found PM10 reduction potentials of up to 70% with the coated and ceramic discs, while documenting the difficulties: bedding procedures are hard to universalise, emissions evolve from unconditioned pads until they stabilise, and disc temperature is a challenging control variable. Gong et al. (2026) added a formulation comparison: NAO pads ran hotter than LM pads, LM pads produced PM2.5 and PM10 emission factors averaging about 3.0 and 6.0 mg per brake-kilometre, roughly an order of magnitude above NAO, and a dominant particle number peak appeared for LM under high-speed sudden deceleration. Ranked by influence, the factors were friction material type, then high-speed sudden deceleration, then temperature. Stępień (2024) describes a field whose measurement and assessment methods for this particle category had been unstandardised.

What the limit implies for discs, pads and calipers

Four engineering levers become commercially relevant once a number exists.

  • Friction formulation. Material type is the first-order variable, with an order-of-magnitude PM10 difference between LM and NAO pads in Gong et al. (2026). Low-dust formulations are a measurable direction, with documented trade-offs: NAO pads ran hotter, and LM pads showed a particle number spike under severe stops.
  • Disc surface and material. Wear-resistant surfaces attack it from the disc side. The coated and carbon ceramic discs tested by Hesse et al. (2021) delivered up to 70% lower PM10 over the WLTP brake cycle, attributed primarily to disc wear resistance and additionally to pad composition and friction-contact temperature. Coating also changes service behaviour: Cai et al. (2025) examined how corrosion influences wear and brake particle emissions of alumina-coated versus uncoated cast iron discs, which connects to the failure modes discussed in our note on brake judder, DTV and corrosion.
  • Caliper drag. Antanaitis (2012) notes that as little as a tenth of a millimetre of pad movement brings pads into full contact, and that a disc brake usually runs with residual drag when released, so pads contact the rotor constantly. That study measured drag, not particles, but the mechanism maps onto the regulation: contact in the released state is wear without braking demand, so a brake caliper that retracts cleanly is a particle-control device as well as a fuel-economy one.
  • Regenerative blending and actuation. The clearest measured effect is a control strategy, not a material. Hagino (2024) tested a regenerative-friction brake coordination system from plug-in hybrids and found it cut emissions by 85% for PM10, 78% for PM2.5 and 87% for particle number against a combustion-vehicle system, with friction work linear in PM10 and PM2.5. How much friction braking remains, and when, is a software and actuator question: implementing acts must cover measurement of real driving brake particle emissions and regenerative braking, and Annex III Table 12 lists optional checks on the share of friction braking. Brake-by-wire can make that blending and drag control programmable rather than a hydraulic side-effect; the actuator shift is covered in our article on brake boosters moving from vacuum to electric assist.

A fifth implication is procedural. Because the regulated object is a vehicle type, the evidence that matters for parts is traceability of the friction pair: which pad formulation, disc specification, caliper build and batch. Implementing acts are to cover brake system types and their replacement parts in respect to particle emissions, and the production-conformity brake test in Table 11 means consistency of manufacture, not only design intent, is checked. A brake disc and drum range that cannot state its material and coating, or a pad range that cannot state its formulation family, is poorly placed to answer that question.

The inverted compliance burden

The analytically interesting part is that the strictest brake limit, 3 mg/km, is given to the powertrain that uses its friction brakes least per kilometre. Regenerative braking already cuts measured brake PM10 by 85% in the system tested by Hagino (2024), so a PEV starts with a margin that comes from how it is driven, not how its pads are made. What it really constrains is the residue: cold starts, high state of charge, high loads and emergency stops. It is a technology-forcing ceiling on the friction pair for the moments when it is used, not an expectation that a PEV wears its brakes like a combustion car. Direct comparisons of electrified and conventional vehicles under real-world driving are now being attempted (Woo et al., 2026).

The fleet arithmetic points the other way. Eurostat data for the EU27 put battery-electric cars at 0.42% of new passenger car registrations in 2015 and 13.52% in 2024, but the same source puts the EU27 passenger car fleet at 260,195,837 vehicles in 2024, up from 221,705,164 in 2013. The 1,455,122 battery-electric cars registered in 2024 equal about 0.56% of the 2024 fleet; the registration years reported here (2015 and 2019-2024) sum to about 5.85 million, roughly 2.2% of the fleet before scrappage. The 7 mg/km limit therefore governs the vehicles that will occupy service bays for years, while the 3 mg/km limit governs a small but growing share of new vehicles. Near term, the specifications chosen to meet 7 mg/km, not the PEV limit, will determine which friction pairs move in volume. Longer term the logic inverts: with Table 8 pointing to 3 mg/km for all M1 and N1 powertrains in 2035, the PEV limit describes the destination technology for everyone.

There is a second inversion. The regulation tests new vehicles with the manufacturer's friction pair, but the in-service fleet runs on replacement pads and discs, so emissions performance after the first pad change is determined by aftermarket parts. That is why the inclusion of replacement parts in the implementing-act scope matters: it is where a vehicle limit could become an evidence requirement on parts.

What to watch

Several questions are open, on a timetable the regulation already fixes. The Commission's brake particle review report is due by 31 December 2027 and will feed delegated acts setting the 2030 second-stage limits in Tables 5 to 8, which introduce a particle number metric alongside PM10 mass. The implementing acts must define how real driving brake particle emissions and regenerative braking are measured, and how the share of friction braking is verified. The 2035 convergence to 3 mg/km sets the direction for coated discs, low-dust friction formulations and low-drag calipers. Whether part-level requirements for replacement brake systems follow, and how quickly, is the open question that matters most for the disc, pad and caliper trade; the News Center and the full product catalog are where the parts side will surface.

References

  1. Antanaitis, D. B. (2012). Vehicle integration factors affecting brake caliper drag. SAE International Journal of Passenger Cars - Mechanical Systems, 5(4), 1244-1258. https://doi.org/10.4271/2012-01-1830
  2. Cai, R., Nie, X., Lyu, Y., & Wahlström, J. (2025). Influence of corrosion on wear and brake particle emissions of alumina-coated and uncoated cast iron brake discs. Surface and Coatings Technology, 516, 132765. https://doi.org/10.1016/j.surfcoat.2025.132765
  3. Christou, A., Giechaskiel, B., Olofsson, U., & Grigoratos, T. (2025). Review of health effects of automotive brake and tyre wear particles. Toxics, 13(4), 301. https://doi.org/10.3390/toxics13040301
  4. Gong, B., Lyu, Y., Xu, Y., Gu, Y., Jiang, N., Zeng, Z., Lyu, Q., Xu, H., Peng, Y., Zeng, G., & Huang, X. (2026). Decoupling the role of pad materials in brake wear particulate emissions using the UN GTR-24 test method toward non-exhaust PM management. Journal of Hazardous Materials, 512, 142369. https://doi.org/10.1016/j.jhazmat.2026.142369
  5. Grigoratos, T., & Martini, G. (2014). Brake wear particle emissions: a review. Environmental Science and Pollution Research, 22(4), 2491-2504. https://doi.org/10.1007/s11356-014-3696-8
  6. Hagino, H. (2024). Feasibility of measuring brake-wear particle emissions from a regenerative-friction brake coordination system via dynamometer testing. Atmosphere, 15(1), 75. https://doi.org/10.3390/atmos15010075
  7. Hesse, D., Hamatschek, C., Augsburg, K., Weigelt, T., Prahst, A., & Gramstat, S. (2021). Testing of alternative disc brakes and friction materials regarding brake wear particle emissions and temperature behavior. Atmosphere, 12(4), 436. https://doi.org/10.3390/atmos12040436
  8. Mathissen, M., Grochowicz, J., Schmidt, C., Vogt, R., Farwick zum Hagen, F. H., Grabiec, T., Steven, H., & Grigoratos, T. (2018). A novel real-world braking cycle for studying brake wear particle emissions. Wear, 414-415, 219-226. https://doi.org/10.1016/j.wear.2018.07.020
  9. Stępień, Z. (2024). Vehicle related non exhaust particle emissions - Euro 7 requirements. Combustion Engines, 199(4), 15-29. https://doi.org/10.19206/ce-190606
  10. Woo, S.-H., Kim, W., Kim, M., Jang, H., & Lee, S. (2026). Impact of vehicle electrification on brake wear particle (BWP) emissions under real-world driving conditions. Wear, 584-585, 206392. https://doi.org/10.1016/j.wear.2025.206392

Data sources

Regulation text. Regulation (EU) 2024/1257 of the European Parliament and of the Council of 24 April 2024 on type-approval of motor vehicles and engines and of systems, components and separate technical units intended for such vehicles, with respect to their emissions and battery durability (Euro 7), Official Journal of the European Union, OJ L, 2024/1257, 8 May 2024. Used for Annex I Table 4 (brake particle limits), Annex III Table 4 (UN GTR No. 24 test basis), Annex III Tables 11 and 12 (brake test at type-approval, conformity of production and optional friction-share verification), Article 6(3)(i) and 6(4)(g) (implementing acts on brake systems and their replacement parts), Article 15(2)(a) (delegated acts on second-stage limits), Article 18(5) (review report due 31 December 2027) and Article 21 (application dates). https://eur-lex.europa.eu/eli/reg/2024/1257/oj

Eurostat, road_eqr_carpda. New passenger cars by type of motor energy, EU27_2020, annual, 2015-2024. Battery-electric (ELC) share of new passenger car registrations: 0.42% (2015), 1.89% (2019), 5.32% (2020), 8.96% (2021), 12.07% (2022), 14.53% (2023), 13.52% (2024); 1,455,122 battery-electric registrations in 2024 against 10,759,893 total. https://ec.europa.eu/eurostat/databrowser/view/road_eqr_carpda/default/table

Eurostat, road_eqs_carage. Passenger cars by age, EU27_2020, total, annual, 2013-2024. Fleet: 221,705,164 passenger cars (2013) and 260,195,837 (2024). Derived ratios in the article (0.56% and 2.2%) are the author's calculations from these two Eurostat series. https://ec.europa.eu/eurostat/databrowser/view/road_eqs_carage/default/table

Need a fitment check?

Send a photograph of the unit, the number on the housing and the vehicle. We will confirm the application and the price.

autoparts@fiverhope.com +86 150 8665 4540
Request a quote