FIVER POWER BRAKE PARTS | Chongqing, China · since 2005

Design, manufacture and distribution of
auto power brake parts
and electric parts

Index: Power brake booster Brake caliper Master cylinder

From Manifold Vacuum to Electric Assist: How Electrification Is Redesigning Brake Boosters

How electrification removes vacuum from brake boosters, and what replaces it: electric pumps, hydro-boost, electro-hydraulic and electro-mechanical brakes.

Electric cars do not need engine vacuum, and that single fact ripples through the brake system. A vacuum brake booster works because a petrol or diesel engine continuously pumps air out of its intake manifold; the booster turns that pressure difference into extra pedal force. Remove the engine and the pressure difference has to be manufactured instead — with an electric pump, a hydraulic circuit, a motor-driven booster or an electric caliper. That is one of the clearest examples of electrification changing the parts around the powertrain.

The stakes are visible in registration data. Battery-electric cars were 0.42% of new EU passenger cars in 2015 (46,669 of 11,107,413) and 13.52% in 2024 (1,455,122 of 10,759,893), according to the road_eqr_carpda table published by Eurostat (2026). Globally, the International Energy Agency (IEA) reports that electric car sales exceeded 17 million in 2024 at a sales share of more than 20% (IEA, 2025). Every battery-electric vehicle was designed without a manifold vacuum source, which is why a component that barely changed for decades is now a site of active engineering.

What manifold vacuum was doing

Inside a vacuum booster, a control valve admits atmospheric air to one side of a diaphragm while the other side is held at low pressure. The pressure difference, multiplied by the diaphragm's effective area, produces most of the force that pushes the master-cylinder piston, and a reaction disc feeds a fraction of that force back to the pedal so the driver still senses load. Vacuum is a by-product of throttled engine operation, not a controlled input. Electrification removes the by-product, and with it the assumption that assist is always available.

Stopgap one: an electric vacuum pump and a reservoir

The most conservative answer keeps the booster and adds a pump. A small electric vane pump evacuates a reservoir, a check valve holds the vacuum, and a control strategy runs the pump when stored vacuum falls below a threshold. Rundo and Squarcini (2013) modelled the single-vane pumps used for pneumatically actuated brake boosters because performance depends on chamber geometry, leakage and the fraction of lubricating oil, especially during cold starts; their tests matched simulated pressure and torque behaviour. Pump displacement, leakage and cold behaviour therefore decide how quickly vacuum recovers after repeated pedal applications.

Control matters as much as hardware. Dake, Mohan and Mullapudi (2019) used machine learning to optimise the on/off strategy of an electric vehicle vacuum pump, treating the switching law, not just pump size, as a design variable. The trade-offs are familiar from diesels: assist is only as good as the stored vacuum, repeated applications deplete it, and cold starts or high altitude are the hard cases. For the aftermarket, the significant change is that the pump becomes a wear item with its own failure modes, and vacuum-level diagnosis becomes part of brake service.

Stopgap two: hydraulic assist without manifold vacuum

Hydro-boost, the hydraulic brake booster approach, takes assist from hydraulic pressure rather than air pressure. Klein (1983) traced the development of hydraulic brake boosters from duo-medium systems that used the steering pump as a power source to single-medium high-pressure designs, and noted the value of power assistance that is independent of the engine's vacuum supply. That independence suits electrified vehicles; the catch is that the pressure source must now be an electric pump, shifting the problem to capacity, stored pressure, heat and packaging. The pedal stays hydraulically connected to the master cylinder, so force-travel feel remains continuous and familiar, and both families remain in production.

Decoupling the pedal: electro-hydraulic brakes

The next step separates the pedal from hydraulic pressure entirely. A survey of brake-by-wire systems for intelligent connected electric vehicles describes substantial changes in structure and control that increased safety and energy recovery while integrating more functions (Meng et al., 2020). In an electro-hydraulic brake (EHB) system the pedal acts on a feel simulator and a motor-driven actuator builds pressure in the hydraulic circuit. Ma et al. (2022) proposed an EHB system whose feel simulator reproduces arbitrary pedal characteristics by controlling motor torque, and which keeps working after faults: if the pedal-travel sensor fails, pedal displacement is estimated from master-cylinder pressure; if the simulator motor fails, a valve controls that pressure to preserve the pedal characteristic. Simulations showed fast pressure response and essentially unchanged pedal feel before and after those faults.

Architectures range from a two-box layout, with a separate actuator and stability-control unit, to a single one-box unit, which matters for packaging and service, because pedal feel is now defined in software rather than by a spring and a diaphragm. The hydraulic circuit has not disappeared, though: fluid, seals, a master cylinder and calipers remain in the force path, and bleeding and pressure diagnostics remain part of the job.

Regenerative blending: friction becomes the follower

In an electric vehicle the motor can brake the car, and the friction brakes fill in whatever the motor and battery cannot absorb. The two torque sources have different dynamics and the handover must be invisible. Caliskan and Patoglu (2020) tested haptic pedal-feel compensation in a simulated driving task and found that preserving natural pedal feel significantly reduced hard-braking instances, improving safety in both two-pedal cooperative braking and one-pedal driving; volunteers strongly preferred compensation, and the benefit was larger in the two-pedal case, where the absence of compensation produced stiffening or softening feel. Ghanami and Nikzadfar (2025) approached the problem from the control side with a hierarchical controller: a high-level layer distributes torque between hydraulic and regenerative braking, a mid-level layer regulates tyre slip, and a low-level layer governs actuator dynamics, with robust slip control and improved energy recovery. The friction brake is therefore commanded rather than directly felt, and pedal feel becomes a design variable that can be tuned — or got wrong.

Removing the fluid: electro-mechanical brakes

At the far end of the spectrum, an electro-mechanical brake (EMB) replaces the hydraulic caliper with an electric motor, a reduction gear and a clamping mechanism at each corner. The control problem becomes clamp-force control: the actuator must close a small air gap quickly, then track force precisely without overshoot. Lee and Manzie (2012) developed a controller based on a time-optimal switching curve derived from Pontryagin's Maximum Principle and implemented it on a production-ready prototype EMB, reporting significant improvements in step response and dynamic tracking relative to benchmark controllers. Meng et al. (2023) discussed booster-motor design for brake-by-wire systems in intelligent electric vehicles, including the functional-safety questions that arise when a motor provides the assist. EMB removes the fluid but raises the bar for sensing, redundancy and heat management at the corner.

What changes in wear and in the workshop

Less friction braking means less friction wear, and the effect is measurable. Hagino (2024) tested a regenerative-friction brake coordination system from commercially available plug-in hybrid electric vehicles and found reductions of 85% for PM10, 78% for PM2.5 and 87% for particle number compared with the system in internal-combustion vehicles; brake friction work showed a linear relationship with PM10 and PM2.5. Nanoparticle emissions rose slightly with regenerative braking but did not contribute significantly to overall particulate mass, while high concentrations of nuclei-mode particles below 20 nm appeared under high-temperature, high-load braking with full-friction brakes.

A friction brake that is used less does not disappear. Discs still corrode when a car sits, calipers still have to release cleanly, and low-use brakes can develop the same judder and thickness-variation problems as high-use ones, so the inspection logic in our article on judder, DTV and corrosion remains relevant as friction work falls. What shifts is the balance: wear-driven failures may become less common relative to corrosion-driven and standstill-related ones, and condition-based checks matter more than mileage alone.

The installed fleet turns over far more slowly than the showroom

New-car technology and the vehicle parc are two different clocks. Eurostat's road_eqs_carage data put the EU passenger car fleet at 221,705,164 in 2013 and 260,195,837 in 2024, an increase of 17.36% (derived from Eurostat, 2026). Over the same period battery-electric cars went from 0.42% to 13.52% of new registrations, but 86.48% of the EU's 2024 new cars were still not battery-electric (derived from the same table). At the 2024 sales rate of 10,759,893 new cars, replacing the entire current fleet once would take about 24 years before any growth is counted (derived from the same data). Table 1 shows the registration shift that is often mistaken for a fleet shift.

Table 1. Battery-electric share of new EU passenger cars, 2015-2024 (Eurostat road_eqr_carpda, EU27)

YearBEV registrationsTotal new passenger carsBEV share
201546,66911,107,4130.42%
2019250,08213,235,7681.89%
2020538,92710,131,0165.32%
2021885,0389,881,8578.96%
20221,129,7869,360,70212.07%
20231,547,67610,654,67614.53%
20241,455,12210,759,89313.52%

The picture is not monotonic: derived from the same table, EU BEV registrations in 2024 were about 6% below their 2023 level while the total market was almost flat. Globally the IEA expects sales to exceed 20 million and more than one-quarter of cars sold in 2025, an electric share above 40% by 2030 under today's policy settings, and notes that China is responsible for more than 70% of global EV production (IEA, 2025). Fast change at the top of the market and slow change in the parc are both true at once.

What to watch

The transition is best understood as a coexistence of assist technologies rather than a replacement. The questions worth tracking are technical:

  • How pedal-feel simulators behave after sensor or motor faults, and whether research fallback strategies reach production diagnostics (Ma et al., 2022).
  • Whether blending controllers can maximise energy recovery without degrading anti-lock performance or pedal consistency (Ghanami & Nikzadfar, 2025; Caliskan & Patoglu, 2020).
  • Where the practical limit of EMB clamp-force control and sensing lies outside prototype programmes (Lee & Manzie, 2012).
  • How electric vacuum pump control trades noise, energy and durability over a full service life (Rundo & Squarcini, 2013; Dake et al., 2019).
  • How brake-wear particle measurement should be defined when friction brakes are deliberately used less (Hagino, 2024).

For the parts business, the consequence is that the hardware splits into two populations. New vehicles increasingly carry electric pumps, motor-driven boosters and, eventually, electric calipers; the vehicles already on the road continue to carry vacuum boosters, vacuum pumps, hydro-boost units and conventional hydraulic calipers for years. FIVER's current range still lists power brake boosters, booster vacuum pumps, brake calipers and the hydraulic parts that go with them, which reflects the size and inertia of the installed fleet rather than nostalgia.

The engineering question for the next decade is not whether vacuum assist eventually disappears from new vehicles, but how the industry manages a long overlap in which a workshop may see an older vacuum-boosted diesel and a new one-box electric car on the same day. The pedal-feel fundamentals do not change with the actuator; only the device that produces the force does.

About the parts discussed

FIVER Auto Parts Co., Ltd designs, manufactures and supplies the brake hardware discussed in this note — vacuum power brake boosters, hydraulic (hydro-boost) boosters, booster vacuum pumps, master cylinders, calipers, discs and drums — from its own facility in Chongqing, China, with a sales network reaching more than 20 countries. The company publishes its process position as following ISO/TS16949 quality management system guidelines, 100% online checking, and 100% vacuum testing of every vacuum power brake booster. If you are specifying a replacement unit for an older or a newer vehicle, send the OE number, the vehicle details or a photograph of the old unit and we will reply with fitment and price.

References

  1. Umut Caliskan, & Volkan Patoglu (2020). Efficacy of Haptic Pedal Feel Compensation on Driving With Regenerative Braking. IEEE Transactions on Haptics, 13(1), 175-182. https://doi.org/10.1109/toh.2020.2967394
  2. Prudhvi Dake, Somanathan Mohan, & Dattatreyudu Mullapudi (2019). Machine learning based EV vacuum pump on/off strategy optimization tool. 2019 IEEE Transportation Electrification Conference (ITEC-India), 1-5. https://doi.org/10.1109/itec-india48457.2019.itecindia2019-110
  3. Nastaran Ghanami, & Kamyar Nikzadfar (2025). A novel hierarchical controller for efficient and safe blending of hydraulic and regenerative braking systems in electric vehicles. International Journal of Dynamics and Control, 13(9). https://doi.org/10.1007/s40435-025-01808-1
  4. Hiroyuki Hagino (2024). Feasibility of Measuring Brake-Wear Particle Emissions from a Regenerative-Friction Brake Coordination System via Dynamometer Testing. Atmosphere, 15(1), 75. https://doi.org/10.3390/atmos15010075
  5. Hans-Christof Klein (1983). Development, Status and Future Trends for Hydraulic Brake Boosters. SAE Technical Paper Series, Paper 830414. https://doi.org/10.4271/830414
  6. Chih Feng Lee, & Chris Manzie (2012). High-Bandwidth Clamp Force Control for an Electromechanical Brake. SAE International Journal of Passenger Cars - Electronic and Electrical Systems, 5(2), 590-599. https://doi.org/10.4271/2012-01-1799
  7. Chengcheng Ma, Xuanyao Wang, Tongliang Xu, Jianye Wang, & Peng Feng (2022). Research on a novel electro-hydraulic brake system and pedal feel control strategy. Proceedings of the Institution of Mechanical Engineers, Part D: Journal of Automobile Engineering, 237(7), 1681-1694. https://doi.org/10.1177/09544070221096185
  8. Bumin Meng, Feifan Yang, Jingang Liu, & Yaonan Wang (2020). A Survey of Brake-by-Wire System for Intelligent Connected Electric Vehicles. IEEE Access, 8, 225424-225436. https://doi.org/10.1109/access.2020.3040184
  9. Bumin Meng, Zhengzhao Zhou, Congyue Zhang, & Feifan Yang (2023). A design method for booster motor of brake-by-wire system based on intelligent electric vehicle. Green Energy and Intelligent Transportation, 2(4), 100110. https://doi.org/10.1016/j.geits.2023.100110
  10. Massimo Rundo, & Raffaele Squarcini (2013). Modelling and Simulation of Brake Booster Vacuum Pumps. SAE International Journal of Commercial Vehicles, 6(1), 236-248. https://doi.org/10.4271/2013-01-9016
  11. Eurostat. (2026). New passenger cars by type of motor energy (road_eqr_carpda), EU27, 2015-2024 [Data set]. Retrieved 15 November 2026, from https://ec.europa.eu/eurostat/databrowser/view/road_eqr_carpda/default/table?lang=en
  12. Eurostat. (2026). Passenger cars by age (road_eqs_carage), EU27, 2013-2024 [Data set]. Retrieved 15 November 2026, from https://ec.europa.eu/eurostat/databrowser/view/road_eqs_carage/default/table?lang=en
  13. International Energy Agency (IEA). (2025). Global EV Outlook 2025: Executive summary. Retrieved 15 November 2026, from https://www.iea.org/reports/global-ev-outlook-2025/executive-summary

Need a fitment check?

Send a photograph of the unit, the number on the housing and the vehicle. We will confirm the application and the price.

autoparts@fiverhope.com +86 150 8665 4540
Request a quote